You are not logged in.

#1 2018-07-14 07:27:58

Cooleech
Member
From: Split, Croatia
Registered: 2018-06-23
Posts: 12

Wi-Fi not working after upgrade

Hi, everyone!
Recently I turned on my Asus EEE netbook and found out that wi-fi cannot connect to my wireless network. My cellphone works just fine with it. I triplechecked my password and it's just fine. I tried downgrading kernel, wireless-tools, networkmanager.. etc. basically all I could find in /var/cache/pacman/pkg that has to do with wireless. Few packages have only one package available so I didn't try to reinstall those.

Here's my dmesg:

dmesg
[    0.306702] Unpacking initramfs...
[    0.649213] Freeing initrd memory: 6788K
[    0.649540] apm: BIOS not found.
[    0.649643] Scanning for low memory corruption every 60 seconds
[    0.651324] Initialise system trusted keyrings
[    0.651361] Key type blacklist registered
[    0.651517] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    0.656825] zbud: loaded
[    0.657277] pstore: using lz4hc compression
[    0.661770] Key type asymmetric registered
[    0.661778] Asymmetric key parser 'x509' registered
[    0.661819] bounce: pool size: 64 pages
[    0.661882] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.662009] io scheduler noop registered
[    0.662014] io scheduler deadline registered
[    0.662246] io scheduler cfq registered (default)
[    0.662252] io scheduler mq-deadline registered
[    0.662255] io scheduler kyber registered
[    0.662418] io scheduler bfq registered
[    0.663149] pcieport 0000:00:1c.0: enabling device (0104 -> 0107)
[    0.663575] pcieport 0000:00:1c.1: enabling device (0106 -> 0107)
[    0.664492] vesafb: mode is 800x600x32, linelength=3200, pages=0
[    0.664496] vesafb: scrolling: redraw
[    0.664501] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.664532] vesafb: framebuffer at 0xd0000000, mapped to 0x(ptrval), using 1920k, total 1920k
[    0.688887] Console: switching to colour frame buffer device 100x37
[    0.712387] fb0: VESA VGA frame buffer device
[    0.712474] intel_idle: MWAIT substates: 0x20220
[    0.712478] intel_idle: v0.4.1 model 0x1C
[    0.712492] tsc: Marking TSC unstable due to TSC halts in idle states deeper than C2
[    0.712651] clocksource: Switched to clocksource hpet
[    0.712896] intel_idle: lapic_timer_reliable_states 0x2
[    0.713103] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    0.713131] ACPI: Lid Switch [LID]
[    0.713274] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[    0.713303] ACPI: Sleep Button [SLPB]
[    0.713428] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[    0.713461] ACPI: Power Button [PWRB]
[    0.713602] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    0.713655] ACPI: Power Button [PWRF]
[    0.714074] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[    0.714501] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input4
[    0.732292] thermal LNXTHERM:00: registered as thermal_zone0
[    0.732298] ACPI: Thermal Zone [TZ00] (67 C)
[    0.732708] isapnp: Scanning for PnP cards...
[    1.045679] isapnp: No Plug & Play device found
[    1.046064] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.049733] ledtrig-cpu: registered to indicate activity on CPUs
[    1.050571] NET: Registered protocol family 10
[    1.062929] Segment Routing with IPv6
[    1.063003] NET: Registered protocol family 17
[    1.063631] RAS: Correctable Errors collector initialized.
[    1.063753] microcode: sig=0x106c2, pf=0x4, revision=0x212
[    1.063930] microcode: Microcode Update Driver: v2.2.
[    1.063942] Using IPI No-Shortcut mode
[    1.064467] registered taskstats version 1
[    1.064493] Loading compiled-in X.509 certificates
[    1.064547] zswap: loaded using pool lzo/zbud
[    1.076583] Key type big_key registered
[    1.077305]   Magic number: 10:536:166
[    1.077438] hctosys: unable to open rtc device (rtc0)
[    1.077726] Unstable clock detected, switching default tracing clock to "global"
               If you want to keep using the local clock, then add:
                 "trace_clock=local"
               on the kernel command line
[    1.080641] Freeing unused kernel memory: 804K
[    1.080879] Write protecting the kernel text: 6720k
[    1.081088] Write protecting the kernel read-only data: 2916k
[    1.470498] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.490821] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.491054] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.522161] ACPI: bus type USB registered
[    1.522305] usbcore: registered new interface driver usbfs
[    1.522370] usbcore: registered new interface driver hub
[    1.522498] usbcore: registered new device driver usb
[    1.524924] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.525927] ehci-pci: EHCI PCI platform driver
[    1.526970] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    1.527001] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    1.527037] ehci-pci 0000:00:1d.7: debug port 1
[    1.531007] ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
[    1.531075] ehci-pci 0000:00:1d.7: irq 23, io mem 0xf7db7c00
[    1.542351] SCSI subsystem initialized
[    1.543474] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.543766] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.17
[    1.543776] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.543782] usb usb1: Product: EHCI Host Controller
[    1.543788] usb usb1: Manufacturer: Linux 4.17.3-1.0-ARCH ehci_hcd
[    1.543794] usb usb1: SerialNumber: 0000:00:1d.7
[    1.545053] hub 1-0:1.0: USB hub found
[    1.545099] hub 1-0:1.0: 8 ports detected
[    1.547996] uhci_hcd: USB Universal Host Controller Interface driver
[    1.548471] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.548497] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    1.548520] uhci_hcd 0000:00:1d.0: detected 2 ports
[    1.548590] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d400
[    1.550311] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.17
[    1.550321] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.550327] usb usb2: Product: UHCI Host Controller
[    1.550333] usb usb2: Manufacturer: Linux 4.17.3-1.0-ARCH uhci_hcd
[    1.550340] usb usb2: SerialNumber: 0000:00:1d.0
[    1.551109] hub 2-0:1.0: USB hub found
[    1.551150] hub 2-0:1.0: 2 ports detected
[    1.552240] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.552270] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    1.552295] uhci_hcd 0000:00:1d.1: detected 2 ports
[    1.552400] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d480
[    1.552752] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.17
[    1.552762] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.552768] usb usb3: Product: UHCI Host Controller
[    1.552774] usb usb3: Manufacturer: Linux 4.17.3-1.0-ARCH uhci_hcd
[    1.552780] usb usb3: SerialNumber: 0000:00:1d.1
[    1.553538] hub 3-0:1.0: USB hub found
[    1.553591] hub 3-0:1.0: 2 ports detected
[    1.554780] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.554807] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    1.554831] uhci_hcd 0000:00:1d.2: detected 2 ports
[    1.554950] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800
[    1.555294] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.17
[    1.555303] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.555309] usb usb4: Product: UHCI Host Controller
[    1.555316] usb usb4: Manufacturer: Linux 4.17.3-1.0-ARCH uhci_hcd
[    1.555322] usb usb4: SerialNumber: 0000:00:1d.2
[    1.555959] hub 4-0:1.0: USB hub found
[    1.556007] hub 4-0:1.0: 2 ports detected
[    1.557183] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    1.557228] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    1.557253] uhci_hcd 0000:00:1d.3: detected 2 ports
[    1.557365] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d880
[    1.557656] libata version 3.00 loaded.
[    1.557683] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.17
[    1.557691] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.557696] usb usb5: Product: UHCI Host Controller
[    1.557709] usb usb5: Manufacturer: Linux 4.17.3-1.0-ARCH uhci_hcd
[    1.557715] usb usb5: SerialNumber: 0000:00:1d.3
[    1.558341] hub 5-0:1.0: USB hub found
[    1.558380] hub 5-0:1.0: 2 ports detected
[    1.559348] ata_piix 0000:00:1f.1: version 2.13
[    1.575608] scsi host0: ata_piix
[    1.580155] scsi host1: ata_piix
[    1.580454] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    1.580462] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    1.580738] ata2: port disabled--ignoring
[    1.580750] ahci 0000:00:1f.2: version 3.0
[    1.581265] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
[    1.581275] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part 
[    1.584588] scsi host2: ahci
[    1.585084] scsi host3: ahci
[    1.585514] scsi host4: ahci
[    1.585949] scsi host5: ahci
[    1.586142] ata3: SATA max UDMA/133 abar m1024@0xf7db7800 port 0xf7db7900 irq 24
[    1.586147] ata4: DUMMY
[    1.586152] ata5: SATA max UDMA/133 abar m1024@0xf7db7800 port 0xf7db7a00 irq 24
[    1.586155] ata6: DUMMY
[    1.677822] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[    1.880213] usb 1-2: new high-speed USB device number 2 using ehci-pci
[    1.905043] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.906920] ata3.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[    1.910117] ata5: SATA link down (SStatus 0 SControl 300)
[    1.954827] ata3.00: ATA-8: ST9160314AS, 0002SDM1, max UDMA/133
[    1.954838] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    1.969700] ata3.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[    1.970151] ata3.00: configured for UDMA/133
[    1.970677] scsi 2:0:0:0: Direct-Access     ATA      ST9160314AS      SDM1 PQ: 0 ANSI: 5
[    1.989438] sd 2:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    1.989519] sd 2:0:0:0: [sda] Write Protect is off
[    1.989528] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.989663] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.016719] random: fast init done
[    2.030590]  sda: sda1 sda2 sda3
[    2.032563] sd 2:0:0:0: [sda] Attached SCSI disk
[    2.111238] usb 1-2: New USB device found, idVendor=13d3, idProduct=5071, bcdDevice=26.01
[    2.111249] usb 1-2: New USB device strings: Mfr=2, Product=3, SerialNumber=0
[    2.111257] usb 1-2: Product: USB2.0 UVC 1.3M WebCam
[    2.111265] usb 1-2: Manufacturer: GenesysLogic Technology Co., Ltd.
[    2.456785] usb 5-1: new full-speed USB device number 2 using uhci_hcd
[    2.638276] usb 5-1: New USB device found, idVendor=0b05, idProduct=b700, bcdDevice= 2.41
[    2.638293] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.638304] usb 5-1: Product: BT-253
[    2.638316] usb 5-1: Manufacturer: Broadcom Corp
[    2.638327] usb 5-1: SerialNumber: 002243F833A1
[    3.043622] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    4.884072] random: crng init done
[    5.206064] systemd[1]: systemd 239 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN +PCRE2 default-hierarchy=hybrid)
[    5.220480] systemd[1]: Detected architecture x86.
[    5.271014] systemd[1]: Set hostname to <archlinux>.
[    7.503716] systemd[1]: Listening on LVM2 metadata daemon socket.
[    7.504425] systemd[1]: Listening on LVM2 poll daemon socket.
[    7.508964] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[    7.534586] systemd[1]: Listening on Process Core Dump Socket.
[    7.535607] systemd[1]: Created slice User and Session Slice.
[    7.535688] systemd[1]: Reached target Remote File Systems.
[    7.597872] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    7.931299] EXT4-fs (sda1): re-mounted. Opts: (null)
[    8.550198] systemd-journald[214]: Received request to flush runtime journal from PID 1
[   11.462827] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   11.566075] Linux agpgart interface v0.103
[   11.734950] ACPI: Battery Slot [BAT0] (battery present)
[   11.735430] ACPI: AC Adapter [AC0] (off-line)
[   11.859587] eeepc_laptop: Eee PC Hotkey Driver
[   11.859600] eeepc_laptop: wlan hotplug disabled
[   11.859629] eeepc_laptop: Hotkey init flags 0x41
[   11.860923] eeepc_laptop: TYPE (2000000) not reported by BIOS, enabling anyway
[   11.871679] eeepc_laptop: PANELPOWER (4000000) not reported by BIOS, enabling anyway
[   11.886369] eeepc_laptop: TPD (8000000) not reported by BIOS, enabling anyway
[   11.886377] eeepc_laptop: Get control methods supported: 0xe101713
[   11.890659] input: Asus EeePC extra buttons as /devices/platform/eeepc/input/input7
[   11.961011] rtc_cmos 00:01: RTC can wake from S4
[   11.961105] rtc_cmos 00:01: only 24-hr supported
[   12.131212] atl1c 0000:01:00.0: version 1.0.1.1-NAPI
[   12.165815] intel_rng: FWH not detected
[   12.234657] leds_ss4200: no LED devices found
[   12.294391] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   12.346611] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   12.498422] media: Linux media interface: v0.10
[   12.501423] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[   12.501437] cfg80211: failed to load regulatory.db
[   12.534617] input: PC Speaker as /devices/platform/pcspkr/input/input8
[   12.779679] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC269: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   12.779692] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   12.779700] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x15/0x0/0x0/0x0/0x0)
[   12.779706] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[   12.779712] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[   12.779720] snd_hda_codec_realtek hdaudioC0D0:      Mic=0x18
[   12.779727] snd_hda_codec_realtek hdaudioC0D0:      Internal Mic=0x12
[   12.860709] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   12.861022] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   12.891588] Linux video capture interface: v2.00
[   13.346868] Bluetooth: Core ver 2.22
[   13.346946] NET: Registered protocol family 31
[   13.346950] Bluetooth: HCI device and connection manager initialized
[   13.346964] Bluetooth: HCI socket layer initialized
[   13.346973] Bluetooth: L2CAP socket layer initialized
[   13.347007] Bluetooth: SCO socket layer initialized
[   13.395302] intel_powerclamp: No package C-state available
[   13.421362] intel_powerclamp: No package C-state available
[   13.465228] uvcvideo: Found UVC 1.00 device USB2.0 UVC 1.3M WebCam (13d3:5071)
[   13.512363] uvcvideo 1-2:1.0: Entity type for entity Extension 2 was not initialized!
[   13.512376] uvcvideo 1-2:1.0: Entity type for entity Processing 3 was not initialized!
[   13.512385] uvcvideo 1-2:1.0: Entity type for entity Camera 1 was not initialized!
[   13.512742] input: USB2.0 UVC 1.3M WebCam: USB2.0  as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.0/input/input12
[   13.513124] usbcore: registered new interface driver uvcvideo
[   13.513128] USB Video Class driver (1.1.1)
[   13.780187] Adding 2046804k swap on /dev/sda3.  Priority:-2 extents:1 across:2046804k FS
[   13.847200] ath: phy0: ASPM enabled: 0x42
[   13.847209] ath: EEPROM regdomain: 0x60
[   13.847213] ath: EEPROM indicates we should expect a direct regpair map
[   13.847219] ath: Country alpha2 being used: 00
[   13.847222] ath: Regpair used: 0x60
[   13.879076] psmouse serio1: synaptics: queried max coordinates: x [..5808], y [..4842]
[   13.973737] pci 0000:00:1e.0: PCI bridge to [bus 05]
[   13.990792] pci 0000:00:00.0: Intel 945GME Chipset
[   13.990828] pci 0000:00:00.0: detected gtt size: 262144K total, 262144K mappable
[   13.990927] pci 0000:00:00.0: detected 8192K stolen memory
[   13.991036] checking generic (d0000000 1e0000) vs hw (d0000000 10000000)
[   13.991040] fb: switching to inteldrmfb from VESA VGA
[   13.991114] Console: switching to colour dummy device 80x25
[   13.991528] [drm] Replacing VGA console driver
[   13.991589] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   13.991593] [drm] Driver supports precise vblank timestamp query.
[   13.991620] resource sanity check: requesting [mem 0x000c0000-0x000dffff], which spans more than PCI Bus 0000:00 [mem 0x000d0000-0x000dffff window]
[   13.991632] caller pci_map_rom+0x4c/0xd0 mapping multiple BARs
[   13.994687] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[   14.007334] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1a0b1, caps: 0xd04731/0xa40000/0xa0000/0x0, board id: 0, fw id: 570166
[   14.018854] [drm] RC6 disabled, disabling runtime PM support
[   14.019043] [drm] initialized overlay support
[   14.020524] [drm] Initialized i915 1.6.0 20180308 for 0000:00:02.0 on minor 0
[   14.041713] fbcon: inteldrmfb (fb0) is primary device
[   14.079216] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11
[   14.080834] pci 0000:00:1e.0: PCI bridge to [bus 05]
[   14.082196] usbcore: registered new interface driver btusb
[   14.129368] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   14.148860] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xf7060000, irq=17
[   14.252680] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[   14.367500] gpio_ich: GPIO from 462 to 511 on gpio_ich
[   14.373329] iTCO_vendor_support: vendor-support=0
[   14.436947] atl1c 0000:01:00.0 enp1s0: renamed from eth0
[   14.442970] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[   14.443099] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS
[   14.755527] Console: switching to colour frame buffer device 128x37
[   14.782717] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[   15.239401] ath9k 0000:02:00.0 wlp2s0: renamed from wlan0
[   15.347506] mousedev: PS/2 mouse device common for all mice
[   16.640472] pci 0000:00:1e.0: PCI bridge to [bus 05]
[   16.750959] pci 0000:00:1e.0: PCI bridge to [bus 05]
[   22.189932] IPv6: ADDRCONF(NETDEV_UP): enp1s0: link is not ready
[   22.191342] atl1c 0000:01:00.0: atl1c: enp1s0 NIC Link is Up<100 Mbps Full Duplex>
[   22.216203] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[   22.232493] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[   22.260636] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[   23.339884] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[   32.481994] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[   33.974696] wlp2s0: authenticate with 08:95:2a:e4:df:ca
[   33.989326] wlp2s0: send auth to 08:95:2a:e4:df:ca (try 1/3)
[   34.083938] wlp2s0: authenticated
[   34.088735] wlp2s0: associate with 08:95:2a:e4:df:ca (try 1/3)
[   34.187368] wlp2s0: RX AssocResp from 08:95:2a:e4:df:ca (capab=0x1411 status=0 aid=1)
[   34.187605] wlp2s0: associated
[   34.193392] wlp2s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 08:95:2a:e4:df:ca
[   34.449238] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[   36.798589] fuse init (API version 7.26)
[   69.344790] atl1c 0000:01:00.0: atl1c: enp1s0 NIC Link is Down
[   80.046259] wlp2s0: deauthenticating from 08:95:2a:e4:df:ca by local choice (Reason: 3=DEAUTH_LEAVING)
[   80.119290] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[   81.557290] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[   82.867019] wlp2s0: authenticate with 08:95:2a:e4:df:ca
[   82.905546] wlp2s0: send auth to 08:95:2a:e4:df:ca (try 1/3)
[   82.929160] wlp2s0: authenticated
[   82.930648] wlp2s0: associate with 08:95:2a:e4:df:ca (try 1/3)
[   82.934440] wlp2s0: RX AssocResp from 08:95:2a:e4:df:ca (capab=0x1411 status=0 aid=1)
[   82.934693] wlp2s0: associated
[   82.936942] wlp2s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 08:95:2a:e4:df:ca
[   83.137116] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[   98.402812] perf: interrupt took too long (2539 > 2500), lowering kernel.perf_event_max_sample_rate to 78600
[  128.037420] wlp2s0: deauthenticating from 08:95:2a:e4:df:ca by local choice (Reason: 3=DEAUTH_LEAVING)
[  128.078583] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  129.479197] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  130.738408] wlp2s0: authenticate with 08:95:2a:e4:df:ca
[  130.753108] wlp2s0: send auth to 08:95:2a:e4:df:ca (try 1/3)
[  130.755222] wlp2s0: authenticated
[  130.760106] wlp2s0: associate with 08:95:2a:e4:df:ca (try 1/3)
[  130.815692] wlp2s0: RX AssocResp from 08:95:2a:e4:df:ca (capab=0x1411 status=0 aid=1)
[  130.815917] wlp2s0: associated
[  130.849548] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[  130.861581] wlp2s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 08:95:2a:e4:df:ca
[  176.039361] wlp2s0: deauthenticating from 08:95:2a:e4:df:ca by local choice (Reason: 3=DEAUTH_LEAVING)
[  176.084261] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  177.455416] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  178.727204] wlp2s0: authenticate with 08:95:2a:e4:df:ca
[  178.760305] wlp2s0: send auth to 08:95:2a:e4:df:ca (try 1/3)
[  178.776588] wlp2s0: authenticated
[  178.780101] wlp2s0: associate with 08:95:2a:e4:df:ca (try 1/3)
[  178.815931] wlp2s0: RX AssocResp from 08:95:2a:e4:df:ca (capab=0x1411 status=0 aid=1)
[  178.816172] wlp2s0: associated
[  178.840493] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[  178.887624] wlp2s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 08:95:2a:e4:df:ca
[  197.239130] perf: interrupt took too long (3216 > 3173), lowering kernel.perf_event_max_sample_rate to 62100
[  224.048067] wlp2s0: deauthenticating from 08:95:2a:e4:df:ca by local choice (Reason: 3=DEAUTH_LEAVING)
[  224.096521] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  348.932718] atl1c 0000:01:00.0: atl1c: enp1s0 NIC Link is Up<100 Mbps Full Duplex>
[  368.044729] perf: interrupt took too long (4052 > 4020), lowering kernel.perf_event_max_sample_rate to 49200
[  445.123586] perf: interrupt took too long (5124 > 5065), lowering kernel.perf_event_max_sample_rate to 39000
[  524.094613] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  525.386913] wlp2s0: authenticate with 08:95:2a:e4:df:ca
[  525.424970] wlp2s0: send auth to 08:95:2a:e4:df:ca (try 1/3)
[  525.505363] wlp2s0: authenticated
[  525.507143] wlp2s0: associate with 08:95:2a:e4:df:ca (try 1/3)
[  525.511385] wlp2s0: RX AssocResp from 08:95:2a:e4:df:ca (capab=0x1411 status=0 aid=1)
[  525.511618] wlp2s0: associated
[  525.714682] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[  525.719151] wlp2s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 08:95:2a:e4:df:ca
[  571.042047] wlp2s0: deauthenticating from 08:95:2a:e4:df:ca by local choice (Reason: 3=DEAUTH_LEAVING)
[  571.310217] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  571.407484] perf: interrupt took too long (6447 > 6405), lowering kernel.perf_event_max_sample_rate to 30900
[  572.578918] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  573.835587] wlp2s0: authenticate with 08:95:2a:e4:df:ca
[  573.858743] wlp2s0: send auth to 08:95:2a:e4:df:ca (try 1/3)
[  573.945271] wlp2s0: authenticated
[  573.950045] wlp2s0: associate with 08:95:2a:e4:df:ca (try 1/3)
[  574.044352] wlp2s0: RX AssocResp from 08:95:2a:e4:df:ca (capab=0x1411 status=0 aid=1)
[  574.044682] wlp2s0: associated
[  574.050421] wlp2s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 08:95:2a:e4:df:ca
[  574.150055] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[  619.040293] wlp2s0: deauthenticating from 08:95:2a:e4:df:ca by local choice (Reason: 3=DEAUTH_LEAVING)
[  619.084635] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  620.404546] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  621.651188] wlp2s0: authenticate with 08:95:2a:e4:df:ca
[  621.667339] wlp2s0: send auth to 08:95:2a:e4:df:ca (try 1/3)
[  621.762204] wlp2s0: authenticated
[  621.763422] wlp2s0: associate with 08:95:2a:e4:df:ca (try 1/3)
[  621.767498] wlp2s0: RX AssocResp from 08:95:2a:e4:df:ca (capab=0x1411 status=0 aid=1)
[  621.767724] wlp2s0: associated
[  621.771732] wlp2s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 08:95:2a:e4:df:ca
[  621.852076] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[  667.040107] wlp2s0: deauthenticating from 08:95:2a:e4:df:ca by local choice (Reason: 3=DEAUTH_LEAVING)
[  667.087756] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  668.417620] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  669.673685] wlp2s0: authenticate with 08:95:2a:e4:df:ca
[  669.688587] wlp2s0: send auth to 08:95:2a:e4:df:ca (try 1/3)
[  669.788230] wlp2s0: authenticated
[  669.790484] wlp2s0: associate with 08:95:2a:e4:df:ca (try 1/3)
[  669.819931] wlp2s0: RX AssocResp from 08:95:2a:e4:df:ca (capab=0x1411 status=0 aid=1)
[  669.820231] wlp2s0: associated
[  669.851954] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[  670.000836] wlp2s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 08:95:2a:e4:df:ca
[  715.062977] wlp2s0: deauthenticating from 08:95:2a:e4:df:ca by local choice (Reason: 3=DEAUTH_LEAVING)
[  715.116407] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[  963.432026] perf: interrupt took too long (8060 > 8058), lowering kernel.perf_event_max_sample_rate to 24600
[ 1015.064931] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 1016.359833] wlp2s0: authenticate with 08:95:2a:e4:df:ca
[ 1016.384495] wlp2s0: send auth to 08:95:2a:e4:df:ca (try 1/3)
[ 1016.415168] wlp2s0: authenticated
[ 1016.417041] wlp2s0: associate with 08:95:2a:e4:df:ca (try 1/3)
[ 1016.421139] wlp2s0: RX AssocResp from 08:95:2a:e4:df:ca (capab=0x1411 status=0 aid=1)
[ 1016.421369] wlp2s0: associated
[ 1016.525792] wlp2s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 08:95:2a:e4:df:ca
[ 1016.622948] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[ 1062.044025] wlp2s0: deauthenticating from 08:95:2a:e4:df:ca by local choice (Reason: 3=DEAUTH_LEAVING)
[ 1062.089890] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 1063.344854] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 1064.613801] wlp2s0: authenticate with 08:95:2a:e4:df:ca
[ 1064.643559] wlp2s0: send auth to 08:95:2a:e4:df:ca (try 1/3)
[ 1064.645950] wlp2s0: authenticated
[ 1064.650027] wlp2s0: associate with 08:95:2a:e4:df:ca (try 1/3)
[ 1064.749457] wlp2s0: RX AssocResp from 08:95:2a:e4:df:ca (capab=0x1411 status=0 aid=1)
[ 1064.749696] wlp2s0: associated
[ 1064.757436] wlp2s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 08:95:2a:e4:df:ca
[ 1064.845464] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready

Here's lspci:

lspci | grep -i network
02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

Part of cat /var/log/pacman.log (since last time it worked correctly):

[2018-07-08 07:43] [PACMAN] Running 'pacman -Syu'
[2018-07-08 07:43] [PACMAN] synchronizing package lists
[2018-07-08 07:44] [PACMAN] starting full system upgrade
[2018-07-08 07:46] [PACMAN] Running 'pacman -Syu --noconfirm'
[2018-07-08 07:46] [PACMAN] synchronizing package lists
[2018-07-08 07:46] [PACMAN] starting full system upgrade
[2018-07-08 07:52] [ALPM] transaction started
[2018-07-08 07:52] [ALPM] upgraded archlinux-keyring (20180404-1.0 -> 20180627-1.0)
[2018-07-08 07:52] [ALPM-SCRIPTLET] ==> Appending keys from archlinux.gpg...
[2018-07-08 07:52] [ALPM-SCRIPTLET] ==> Locally signing trusted keys in keyring...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Locally signing key DDB867B92AA789C165EEFA799B729B06A680C281...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Locally signing key 684148BB25B49E986A4944C55184252D824B18E8...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Locally signing key 91FFE0700E80619CEB73235CA88E23E377514E00...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Locally signing key AB19265E5D7D20687D303246BA1DFB64FFF979E7...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Locally signing key 0E8B644079F599DFC1DDC3973348882F6AC6A4C2...
[2018-07-08 07:52] [ALPM-SCRIPTLET] ==> Importing owner trust values...
[2018-07-08 07:52] [ALPM-SCRIPTLET] ==> Disabling revoked keys in keyring...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 7FA647CD89891DEDC060287BB9113D1ED21E1A55...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key D4DE5ABDE2A7287644EAC7E36D1A9E70E19DAA50...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 40440DC037C05620984379A6761FAD69BA06C6A9...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key B1F2C889CB2CCB2ADA36D963097D629E437520BD...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key BC1FBE4D2826A0B51E47ED62E2539214C6C11350...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 63F395DE2D6398BBE458F281F2DBB4931985A992...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 8F76BEEA0289F9E1D3E229C05F946DED983D4366...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 4FCF887689C41B09506BE8D5F3E1D5C5D30DB0AD...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 81D7F8241DB38BC759C80FCE3A726C6170E80477...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 5E7585ADFF106BFFBBA319DC654B877A0864983E...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 50F33E2E5B0C3D900424ABE89BDCF497A4BBCC7F...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key E7210A59715F6940CF9A4E36A001876699AD6E84...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key F5A361A3A13554B85E57DDDAAF7EF7873CFD4BB6...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 40776A5221EF5AD468A4906D42A1DB15EC133BAD...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 8CF934E339CAD8ABF342E822E711306E3C4F88BC...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 5696C003B0854206450C8E5BE613C09CB4440678...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 9515D8A8EAB88E49BB65EDBCE6B456CAF15447D5...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 4A8B17E20B88ACA61860009B5CED81B7C2E5C0D2...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 0B20CA1931F5DA3A70D0F8D2EA6836E1AB441196...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 34C5D94FE7E7913E86DC427E7FB1A3800C84C0A5...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 39F880E50E49A4D11341E8F939E4F17F295AFBF4...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 66BD74A036D522F51DD70A3C7F2A16726521E06D...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key DBE7D3DD8C81D58D0A13D0E76BC26A17B9B7018A...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 07DFD3A0BC213FA12EDC217559B3122E2FA915EC...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 44D4A033AC140143927397D47EFD567D4C7EA887...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 27FFC4769E19F096D41D9265A04F9397CDFD6BB0...
[2018-07-08 07:52] [ALPM-SCRIPTLET]   -> Disabling key 8840BD07FC24CB7CE394A07CCF7037A4F27FB7DA...
[2018-07-08 07:52] [ALPM-SCRIPTLET] ==> Updating trust database...
[2018-07-08 07:52] [ALPM-SCRIPTLET] gpg: next trustdb check due at 2018-10-19
[2018-07-08 07:52] [ALPM] upgraded iana-etc (20180221-1.0 -> 20180221-1.2)
[2018-07-08 07:52] [ALPM] upgraded bluez-libs (5.49-4.0 -> 5.50-3.0)
[2018-07-08 07:52] [ALPM] upgraded db (5.3.28-3 -> 5.3.28-4.0)
[2018-07-08 07:52] [ALPM] upgraded ca-certificates-mozilla (3.37.1-1.0 -> 3.38-1.0)
[2018-07-08 07:52] [ALPM] upgraded sqlite (3.23.1-1.0 -> 3.24.0-1.0)
[2018-07-08 07:52] [ALPM] upgraded nss (3.37.1-1.0 -> 3.38-1.0)
[2018-07-08 07:52] [ALPM] upgraded xdg-utils (1.1.2-2.0 -> 1.1.3-2.0)
[2018-07-08 07:52] [ALPM] upgraded libsystemd (238.133-4.0 -> 239.0-2.0)
[2018-07-08 07:52] [ALPM] upgraded libcups (2.2.7-2.0 -> 2.2.8-3.0)
[2018-07-08 07:52] [ALPM] upgraded json-c (0.13-1.0 -> 0.13.1-1.0)
[2018-07-08 07:52] [ALPM] upgraded cryptsetup (2.0.3-2.0 -> 2.0.3-2.1)
[2018-07-08 07:52] [ALPM] upgraded hwids (20171003-1.0 -> 20180518-1.0)
[2018-07-08 07:52] [ALPM] upgraded pam (1.3.0-2.0 -> 1.3.1-1.0)
[2018-07-08 07:52] [ALPM] upgraded libseccomp (2.3.2-2.0 -> 2.3.3-1.0)
[2018-07-08 07:53] [ALPM] upgraded systemd (238.133-4.0 -> 239.0-2.0)
[2018-07-08 07:53] [ALPM] upgraded libpulse (11.1-1 -> 12.0-1.0)
[2018-07-08 07:53] [ALPM] installed aom (1.0.0-1.0)
[2018-07-08 07:53] [ALPM] upgraded fribidi (1.0.2-1.0 -> 1.0.4-1.0)
[2018-07-08 07:53] [ALPM] upgraded lame (3.100-1 -> 3.100-2.0)
[2018-07-08 07:53] [ALPM] upgraded libomxil-bellagio (0.9.3-1.1 -> 0.9.3-2.0)
[2018-07-08 07:53] [ALPM] upgraded openjpeg2 (2.3.0-1 -> 2.3.0-2.0)
[2018-07-08 07:53] [ALPM] upgraded harfbuzz (1.7.6-2.0 -> 1.8.2-1.0)
[2018-07-08 07:53] [ALPM] upgraded libedit (20170329_3.1-1 -> 20180525_3.1-1.0)
[2018-07-08 07:53] [ALPM] upgraded mesa (18.0.4-1.0 -> 18.1.3-1.0)
[2018-07-08 07:53] [ALPM] upgraded speexdsp (1.2rc3-2 -> 1.2rc3-3.0)
[2018-07-08 07:53] [ALPM] upgraded sysfsutils (2.1.0-9 -> 2.1.0-10.0)
[2018-07-08 07:53] [ALPM] upgraded ffmpeg (1:4.0.1-1.0 -> 1:4.0.1-2.0)
[2018-07-08 07:53] [ALPM] upgraded sound-theme-freedesktop (0.8-2 -> 0.8-3.0)
[2018-07-08 07:53] [ALPM] upgraded libxft (2.3.2-1 -> 2.3.2-2.0)
[2018-07-08 07:53] [ALPM] upgraded libdatrie (0.2.10-2 -> 0.2.12-1.0)
[2018-07-08 07:53] [ALPM] upgraded libgusb (0.2.11-1 -> 0.3.0-1.0)
[2018-07-08 07:53] [ALPM] upgraded js52 (52.7.3-2.0 -> 52.9.0-1.0)
[2018-07-08 07:53] [ALPM] upgraded xkeyboard-config (2.23.1-3.0 -> 2.24-1.0)
[2018-07-08 07:53] [ALPM] upgraded chromium (67.0.3396.87-2.0 -> 67.0.3396.87-2.1)
[2018-07-08 07:53] [ALPM] upgraded libwbclient (4.8.2-1.0 -> 4.8.3-1.0)
[2018-07-08 07:53] [ALPM] upgraded cifs-utils (6.7-2 -> 6.8-2.0)
[2018-07-08 07:53] [ALPM] upgraded dmraid (1.0.0.rc16.3-10 -> 1.0.0.rc16.3-11.0)
[2018-07-08 07:53] [ALPM] upgraded ghostscript (9.23-1.0 -> 9.23-1.1)
[2018-07-08 07:53] [ALPM] upgraded ndctl (60.3-1.0 -> 61.1-1.0)
[2018-07-08 07:53] [ALPM] warning: /usr/bin/pinentry installed as /usr/bin/pinentry.pacnew
[2018-07-08 07:53] [ALPM] upgraded pinentry (1.1.0-3.0 -> 1.1.0-4.0)
[2018-07-08 07:53] [ALPM] upgraded volume_key (0.3.10-1.0 -> 0.3.10-1.1)
[2018-07-08 07:53] [ALPM] installed libyaml (0.1.7-1)
[2018-07-08 07:53] [ALPM] upgraded libblockdev (2.17-3.0 -> 2.18-1.1)
[2018-07-08 07:53] [ALPM] upgraded udisks2 (2.7.6-1.0 -> 2.7.6-1.1)
[2018-07-08 07:53] [ALPM] upgraded gnome-disk-utility (3.28.2-1.0 -> 3.28.2-1.1)
[2018-07-08 07:53] [ALPM] upgraded graphene (1.8.0-1.0 -> 1.8.2-1.0)
[2018-07-08 07:53] [ALPM] upgraded grub (2:2.02-5.0 -> 2:2.02-7.0)
[2018-07-08 07:53] [ALPM] upgraded libdca (0.0.5-5 -> 0.0.6-1.0)
[2018-07-08 07:53] [ALPM] upgraded sbc (1.3-1 -> 1.3-2.0)
[2018-07-08 07:53] [ALPM] upgraded ladspa (1.13-6 -> 1.13-7.0)
[2018-07-08 07:53] [ALPM] upgraded spandsp (0.0.6-1 -> 0.0.6-2.0)
[2018-07-08 07:53] [ALPM] upgraded srt (1.3.0-2.0 -> 1.3.1-1.0)
[2018-07-08 07:53] [ALPM] upgraded libnghttp2 (1.31.1-1.0 -> 1.32.0-1.0)
[2018-07-08 07:53] [ALPM] upgraded ilmbase (2.2.1-3.0 -> 2.2.1-4.0)
[2018-07-08 07:53] [ALPM] upgraded gst-plugins-bad (1.14.1-2.0 -> 1.14.1-2.2)
[2018-07-08 07:53] [ALPM] upgraded gtksourceview3 (3.24.7-1.0 -> 3.24.8-1.0)
[2018-07-08 07:53] [ALPM] upgraded gvfs (1.36.2-1.0 -> 1.36.2-2.1)
[2018-07-08 07:53] [ALPM] upgraded harfbuzz-icu (1.7.6-2.0 -> 1.8.2-1.0)
[2018-07-08 07:53] [ALPM] installed lmdb (0.9.22-1.0)
[2018-07-08 07:53] [ALPM] upgraded ldb (1.3.3-1.0 -> 1.4.0-1.0)
[2018-07-08 07:53] [ALPM] upgraded libcacard (2.5.3-1 -> 2.5.3-1.1)
[2018-07-08 07:53] [ALPM] upgraded libfakekey (0.1-7 -> 0.3-1.0)
[2018-07-08 07:53] [ALPM] upgraded libwacom (0.29-1.0 -> 0.30-1.0)
[2018-07-08 07:53] [ALPM] upgraded libinput (1.10.7-1.0 -> 1.11.2-1.0)
[2018-07-08 07:53] [ALPM] upgraded libnm (1.10.8-1.0 -> 1.10.10-1.0)
[2018-07-08 07:53] [ALPM] upgraded libnm-glib (1.10.8-1.0 -> 1.10.10-1.0)
[2018-07-08 07:53] [ALPM] upgraded libtar (1.2.20-3 -> 1.2.20-4.0)
[2018-07-08 07:54] [ALPM] upgraded linux-firmware (20180518.2a9b2cf-1.0 -> 20180606.d114732-1.0)
[2018-07-08 07:54] [ALPM] upgraded linux (4.16.6-1.0 -> 4.17.3-1.0)
[2018-07-08 07:54] [ALPM] upgraded xcb-util (0.4.0-1 -> 0.4.0-2.0)
[2018-07-08 07:54] [ALPM] upgraded mate-desktop (1.20.1-1.0 -> 1.20.3-1.0)
[2018-07-08 07:54] [ALPM] upgraded mate-panel (1.20.1-1.0 -> 1.20.2-1.0)
[2018-07-08 07:54] [ALPM] upgraded mate-applets (1.20.1-1.0 -> 1.20.2-1.0)
[2018-07-08 07:54] [ALPM] upgraded mate-settings-daemon (1.20.1-1.0 -> 1.20.3-1.0)
[2018-07-08 07:54] [ALPM] upgraded netctl (1.16-1.0 -> 1.17-1.0)
[2018-07-08 07:54] [ALPM] upgraded nm-connection-editor (1.8.12-2.0 -> 1.8.14-1.0)
[2018-07-08 07:54] [ALPM] upgraded networkmanager (1.10.8-1.0 -> 1.10.10-1.0)
[2018-07-08 07:54] [ALPM] upgraded network-manager-applet (1.8.12-2.0 -> 1.8.14-1.0)
[2018-07-08 07:54] [ALPM] upgraded openssh (7.7p1-1.0 -> 7.7p1-2.0)
[2018-07-08 07:54] [ALPM] upgraded p7zip (16.02-4.0 -> 16.02-5.0)
[2018-07-08 07:54] [ALPM] upgraded pcmciautils (018-8.0 -> 018-8.1)
[2018-07-08 07:55] [ALPM] upgraded wine (3.9-1.0 -> 3.11-1.0)
[2018-07-08 07:55] [ALPM] upgraded playonlinux (4.2.12-1 -> 4.2.12-2.0)
[2018-07-08 07:55] [ALPM] upgraded webkit2gtk (2.20.2-1.0 -> 2.20.3-1.0)
[2018-07-08 07:55] [ALPM] upgraded pluma (1.20.1-1.0 -> 1.20.2-1.0)
[2018-07-08 07:55] [ALPM] upgraded poppler (0.64.0-1.0 -> 0.64.0-1.1)
[2018-07-08 07:55] [ALPM] upgraded poppler-glib (0.64.0-1.0 -> 0.64.0-1.1)
[2018-07-08 07:55] [ALPM] upgraded pulseaudio (11.1-1 -> 12.0-1.0)
[2018-07-08 07:55] [ALPM] upgraded xcb-util-keysyms (0.4.0-1 -> 0.4.0-2.0)
[2018-07-08 07:55] [ALPM] upgraded xcb-util-renderutil (0.3.9-1 -> 0.3.9-2.0)
[2018-07-08 07:55] [ALPM] upgraded xcb-util-wm (0.4.1-1 -> 0.4.1-2.0)
[2018-07-08 07:55] [ALPM] upgraded xcb-util-image (0.4.0-1 -> 0.4.0-2.0)
[2018-07-08 07:55] [ALPM] upgraded qt5-base (5.11.0-1.0 -> 5.11.1-1.1)
[2018-07-08 07:55] [ALPM] upgraded pyqt5-common (5.10.1-2.0 -> 5.10.1-6.1)
[2018-07-08 07:55] [ALPM] upgraded python-dbus-common (1.2.6-1.0 -> 1.2.8-1.0)
[2018-07-08 07:55] [ALPM] upgraded python-dbus (1.2.6-1.0 -> 1.2.8-1.0)
[2018-07-08 07:55] [ALPM] upgraded python-pyqt5 (5.10.1-2.0 -> 5.10.1-6.1)
[2018-07-08 07:55] [ALPM] upgraded python-pyudev (0.21.0-2 -> 0.21.0-3.0)
[2018-07-08 07:55] [ALPM] upgraded python2-dbus (1.2.6-1.0 -> 1.2.8-1.0)
[2018-07-08 07:55] [ALPM] upgraded qemu (2.12.0-1.2 -> 2.12.0-1.3)
[2018-07-08 07:56] [ALPM] upgraded qemu-arch-extra (2.12.0-1.2 -> 2.12.0-1.3)
[2018-07-08 07:56] [ALPM] upgraded qt5-svg (5.11.0-1.0 -> 5.11.1-1.0)
[2018-07-08 07:56] [ALPM] upgraded qt5-x11extras (5.11.0-1.0 -> 5.11.1-1.0)
[2018-07-08 07:56] [ALPM] upgraded remmina (1:1.2.30-1.0 -> 1:1.2.30.1-1.1)
[2018-07-08 07:56] [ALPM] upgraded smbclient (4.8.2-1.0 -> 4.8.3-1.0)
[2018-07-08 07:56] [ALPM] warning: directory permissions differ on /var/lib/samba/private/
filesystem: 755  package: 700
[2018-07-08 07:56] [ALPM] upgraded samba (4.8.2-1.0 -> 4.8.3-1.0)
[2018-07-08 07:56] [ALPM] upgraded systemd-sysvcompat (238.133-4.0 -> 239.0-2.0)
[2018-07-08 07:56] [ALPM] upgraded unrar (1:5.6.4-1.0 -> 1:5.6.5-1.0)
[2018-07-08 07:56] [ALPM] upgraded usbutils (009-1.0 -> 010-1.0)
[2018-07-08 07:56] [ALPM] upgraded vlc (3.0.3-1.0 -> 3.0.3-1.1)
[2018-07-08 07:56] [ALPM] upgraded winetricks (20180513-1.0 -> 20180603-1.0)
[2018-07-08 07:56] [ALPM] upgraded xf86-input-mouse (1.9.2-3 -> 1.9.3-1.0)
[2018-07-08 07:56] [ALPM] upgraded xf86-input-synaptics (1.9.0-1 -> 1.9.1-1.0)
[2018-07-08 07:56] [ALPM-SCRIPTLET] >>> xf86-input-synaptics driver is on maintenance mode and
[2018-07-08 07:56] [ALPM-SCRIPTLET]     xf86-input-libinput driver must be prefered over.
[2018-07-08 07:56] [ALPM] upgraded xf86-video-fbdev (0.4.4+13+g9af7f81-1.0 -> 0.5.0-1.0)
[2018-07-08 07:56] [ALPM] upgraded xorg-xkbcomp (1.4.1-1.0 -> 1.4.2-1.0)
[2018-07-08 07:56] [ALPM] upgraded xorg-server-common (1.20.0-5.0 -> 1.20.0-9.0)
[2018-07-08 07:56] [ALPM] upgraded xorg-server (1.20.0-5.0 -> 1.20.0-9.0)
[2018-07-08 07:56] [ALPM] transaction completed
[2018-07-08 07:56] [ALPM] running '60-linux.hook'...
[2018-07-08 07:57] [ALPM] running '90-linux.hook'...
[2018-07-08 07:57] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'default'
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux.img
[2018-07-08 07:57] [ALPM-SCRIPTLET] ==> Starting build: 4.17.3-1.0-ARCH
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [base]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [udev]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [autodetect]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [modconf]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [block]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [filesystems]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [keyboard]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [fsck]
[2018-07-08 07:57] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2018-07-08 07:57] [ALPM-SCRIPTLET] ==> Creating gzip-compressed initcpio image: /boot/initramfs-linux.img
[2018-07-08 07:57] [ALPM-SCRIPTLET] ==> Image generation successful
[2018-07-08 07:57] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'fallback'
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
[2018-07-08 07:57] [ALPM-SCRIPTLET] ==> Starting build: 4.17.3-1.0-ARCH
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [base]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [udev]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [modconf]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [block]
[2018-07-08 07:57] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: wd719x
[2018-07-08 07:57] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: aic94xx
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [filesystems]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [keyboard]
[2018-07-08 07:57] [ALPM-SCRIPTLET]   -> Running build hook: [fsck]
[2018-07-08 07:57] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2018-07-08 07:57] [ALPM-SCRIPTLET] ==> Creating gzip-compressed initcpio image: /boot/initramfs-linux-fallback.img
[2018-07-08 07:58] [ALPM-SCRIPTLET] ==> Image generation successful
[2018-07-08 07:58] [ALPM] running 'gio-querymodules.hook'...
[2018-07-08 07:58] [ALPM] running 'glib-compile-schemas.hook'...
[2018-07-08 07:58] [ALPM] running 'gtk-update-icon-cache.hook'...
[2018-07-08 07:58] [ALPM] running 'gvfsd.hook'...
[2018-07-08 07:58] [ALPM] running 'systemd-binfmt.hook'...
[2018-07-08 07:58] [ALPM] running 'systemd-catalog.hook'...
[2018-07-08 07:58] [ALPM] running 'systemd-daemon-reload.hook'...
[2018-07-08 07:58] [ALPM] running 'systemd-hwdb.hook'...
[2018-07-08 07:58] [ALPM] running 'systemd-sysctl.hook'...
[2018-07-08 07:58] [ALPM] running 'systemd-sysusers.hook'...
[2018-07-08 07:58] [ALPM] running 'systemd-tmpfiles.hook'...
[2018-07-08 07:58] [ALPM] running 'systemd-udev-reload.hook'...
[2018-07-08 07:58] [ALPM] running 'systemd-update.hook'...
[2018-07-08 07:58] [ALPM] running 'texinfo-install.hook'...
[2018-07-08 07:58] [ALPM] running 'update-ca-trust.hook'...
[2018-07-08 07:58] [ALPM] running 'update-desktop-database.hook'...
[2018-07-08 07:58] [ALPM] running 'update-mime-database.hook'...
[2018-07-08 07:58] [ALPM] running 'update-vlc-plugin-cache.hook'...
[2018-11-02 07:19] [PACMAN] Running 'pacman -U linux-4.16.6-1.0-i686.pkg.tar.xz'
[2018-11-02 07:19] [ALPM] transaction started
[2018-11-02 07:20] [ALPM] downgraded linux (4.17.3-1.0 -> 4.16.6-1.0)
[2018-11-02 07:20] [ALPM] transaction completed
[2018-11-02 07:20] [ALPM] running '60-linux.hook'...
[2018-11-02 07:20] [ALPM] running '90-linux.hook'...
[2018-11-02 07:20] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'default'
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux.img
[2018-11-02 07:20] [ALPM-SCRIPTLET] ==> Starting build: 4.16.6-1.0-ARCH
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [base]
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [udev]
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [autodetect]
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [modconf]
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [block]
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [filesystems]
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [keyboard]
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [fsck]
[2018-11-02 07:20] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2018-11-02 07:20] [ALPM-SCRIPTLET] ==> Creating gzip-compressed initcpio image: /boot/initramfs-linux.img
[2018-11-02 07:20] [ALPM-SCRIPTLET] ==> Image generation successful
[2018-11-02 07:20] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'fallback'
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
[2018-11-02 07:20] [ALPM-SCRIPTLET] ==> Starting build: 4.16.6-1.0-ARCH
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [base]
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [udev]
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [modconf]
[2018-11-02 07:20] [ALPM-SCRIPTLET]   -> Running build hook: [block]
[2018-11-02 07:21] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: wd719x
[2018-11-02 07:21] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: aic94xx
[2018-11-02 07:21] [ALPM-SCRIPTLET]   -> Running build hook: [filesystems]
[2018-11-02 07:21] [ALPM-SCRIPTLET]   -> Running build hook: [keyboard]
[2018-11-02 07:21] [ALPM-SCRIPTLET]   -> Running build hook: [fsck]
[2018-11-02 07:21] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2018-11-02 07:21] [ALPM-SCRIPTLET] ==> Creating gzip-compressed initcpio image: /boot/initramfs-linux-fallback.img
[2018-11-02 07:21] [ALPM-SCRIPTLET] ==> Image generation successful
[2018-11-02 07:21] [ALPM] running 'systemd-update.hook'...
[2018-11-02 07:23] [PACMAN] Running 'pacman -U wireless_tools-30.pre9-1-i686.pkg.tar.xz'
[2018-11-02 07:24] [ALPM] transaction started
[2018-11-02 07:24] [ALPM] downgraded wireless_tools (30.pre9-2.0 -> 30.pre9-1)
[2018-11-02 07:24] [ALPM] transaction completed
[2018-11-02 07:24] [ALPM] running 'systemd-update.hook'...
[2018-11-02 07:33] [PACMAN] Running 'pacman -U networkmanager-1.10.8-1.0-i686.pkg.tar.xz'
[2018-11-02 07:33] [ALPM] transaction started
[2018-11-02 07:33] [ALPM] downgraded networkmanager (1.10.10-1.0 -> 1.10.8-1.0)
[2018-11-02 07:33] [ALPM] transaction completed
[2018-11-02 07:33] [ALPM] running 'systemd-daemon-reload.hook'...
[2018-11-02 07:33] [ALPM] running 'systemd-udev-reload.hook'...
[2018-11-02 07:33] [ALPM] running 'systemd-update.hook'...
[2018-11-02 07:38] [PACMAN] Running 'pacman -U network-manager-applet-1.8.12-2.0-i686.pkg.tar.xz'
[2018-11-02 07:38] [ALPM] transaction started
[2018-11-02 07:38] [ALPM] downgraded network-manager-applet (1.8.14-1.0 -> 1.8.12-2.0)
[2018-11-02 07:38] [ALPM] transaction completed
[2018-11-02 07:38] [ALPM] running 'gtk-update-icon-cache.hook'...
[2018-11-02 07:38] [ALPM] running 'systemd-update.hook'...
[2018-11-02 07:38] [ALPM] running 'update-desktop-database.hook'...
[2018-11-02 07:41] [PACMAN] Running 'pacman -U networkmanager-dispatcher-ntpd-1.0-6-any.pkg.tar.xz'
[2018-11-02 07:41] [ALPM] transaction started
[2018-11-02 07:41] [ALPM] downgraded networkmanager-dispatcher-ntpd (1.0-7.0 -> 1.0-6)
[2018-11-02 07:41] [ALPM] transaction completed
[2018-11-02 07:41] [ALPM] running 'systemd-update.hook'...
[2018-11-02 07:42] [PACMAN] Running 'pacman -U nm-connection-editor-1.8.12-2.0-i686.pkg.tar.xz'
[2018-11-02 07:42] [ALPM] transaction started
[2018-11-02 07:42] [ALPM] downgraded nm-connection-editor (1.8.14-1.0 -> 1.8.12-2.0)
[2018-11-02 07:42] [ALPM] transaction completed
[2018-11-02 07:42] [ALPM] running 'glib-compile-schemas.hook'...
[2018-11-02 07:42] [ALPM] running 'gtk-update-icon-cache.hook'...
[2018-11-02 07:42] [ALPM] running 'systemd-update.hook'...
[2018-11-02 07:42] [ALPM] running 'update-desktop-database.hook'...
[2018-11-02 07:59] [PACMAN] Running 'pacman -Rs xf86-video-nouveau'
[2018-07-14 08:56] [PACMAN] Running 'pacman -Syu'
[2018-07-14 08:56] [PACMAN] synchronizing package lists
[2018-07-14 08:56] [PACMAN] starting full system upgrade
[2018-07-14 08:56] [PACMAN] Running 'pacman -Syu --noconfirm'
[2018-07-14 08:56] [PACMAN] synchronizing package lists
[2018-07-14 08:56] [PACMAN] starting full system upgrade
[2018-07-14 08:57] [ALPM] transaction started
[2018-07-14 08:57] [ALPM] upgraded bzip2 (1.0.6-7.0 -> 1.0.6-7.1)
[2018-07-14 08:57] [ALPM] upgraded device-mapper (2.02.177-5.0 -> 2.02.179-1.0)
[2018-07-14 08:57] [ALPM] upgraded krb5 (1.16.1-1.0 -> 1.16.1-1.1)
[2018-07-14 08:57] [ALPM] upgraded linux (4.16.6-1.0 -> 4.17.3-1.0)
[2018-07-14 08:57] [ALPM] upgraded lvm2 (2.02.177-5.0 -> 2.02.179-1.0)
[2018-07-14 08:57] [ALPM] upgraded tar (1.30-1.0 -> 1.30-1.1)
[2018-07-14 08:57] [ALPM] upgraded nm-connection-editor (1.8.12-2.0 -> 1.8.14-1.0)
[2018-07-14 08:57] [ALPM] upgraded networkmanager (1.10.8-1.0 -> 1.10.10-1.0)
[2018-07-14 08:57] [ALPM] upgraded network-manager-applet (1.8.12-2.0 -> 1.8.14-1.0)
[2018-07-14 08:57] [ALPM] upgraded networkmanager-dispatcher-ntpd (1.0-6 -> 1.0-7.0)
[2018-07-14 08:57] [ALPM] warning: /etc/pacman.d/mirrorlist installed as /etc/pacman.d/mirrorlist.pacnew
[2018-07-14 08:57] [ALPM] upgraded pacman-mirrorlist (20180601-1.0 -> 20180708-2.0)
[2018-07-14 08:57] [ALPM] upgraded wireless_tools (30.pre9-1 -> 30.pre9-2.0)
[2018-07-14 08:57] [ALPM] transaction completed
[2018-07-14 08:57] [ALPM] running '60-linux.hook'...
[2018-07-14 08:57] [ALPM] running '90-linux.hook'...
[2018-07-14 08:57] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'default'
[2018-07-14 08:57] [ALPM-SCRIPTLET]   -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux.img
[2018-07-14 08:57] [ALPM-SCRIPTLET] ==> Starting build: 4.17.3-1.0-ARCH
[2018-07-14 08:57] [ALPM-SCRIPTLET]   -> Running build hook: [base]
[2018-07-14 08:57] [ALPM-SCRIPTLET]   -> Running build hook: [udev]
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [autodetect]
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [modconf]
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [block]
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [filesystems]
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [keyboard]
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [fsck]
[2018-07-14 08:58] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2018-07-14 08:58] [ALPM-SCRIPTLET] ==> Creating gzip-compressed initcpio image: /boot/initramfs-linux.img
[2018-07-14 08:58] [ALPM-SCRIPTLET] ==> Image generation successful
[2018-07-14 08:58] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'fallback'
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
[2018-07-14 08:58] [ALPM-SCRIPTLET] ==> Starting build: 4.17.3-1.0-ARCH
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [base]
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [udev]
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [modconf]
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [block]
[2018-07-14 08:58] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: wd719x
[2018-07-14 08:58] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: aic94xx
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [filesystems]
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [keyboard]
[2018-07-14 08:58] [ALPM-SCRIPTLET]   -> Running build hook: [fsck]
[2018-07-14 08:58] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2018-07-14 08:58] [ALPM-SCRIPTLET] ==> Creating gzip-compressed initcpio image: /boot/initramfs-linux-fallback.img
[2018-07-14 08:58] [ALPM-SCRIPTLET] ==> Image generation successful
[2018-07-14 08:58] [ALPM] running 'glib-compile-schemas.hook'...
[2018-07-14 08:58] [ALPM] running 'gtk-update-icon-cache.hook'...
[2018-07-14 08:58] [ALPM] running 'systemd-daemon-reload.hook'...
[2018-07-14 08:58] [ALPM] running 'systemd-udev-reload.hook'...
[2018-07-14 08:58] [ALPM] running 'systemd-update.hook'...
[2018-07-14 08:58] [ALPM] running 'texinfo-install.hook'...
[2018-07-14 08:58] [ALPM] running 'update-desktop-database.hook'...

As you can see, I tried upgrading also. Still no luck. hmm
If you need any more info, please just ask.
Thank you all in advance!

Offline

#2 2018-07-14 07:40:57

Cooleech
Member
From: Split, Croatia
Registered: 2018-06-23
Posts: 12

Re: Wi-Fi not working after upgrade

Please ignore all of above; once I rebooted my router everything works as it should. But I'm still not sure why my cellphone worked just fine on that same network? Oh, well.. hmm

Thanx for reading, I guess.. LOL. big_smile

Offline

Board footer

Powered by FluxBB